Restore from backup

[Spot]

I can't seem to find anything on how to restore my CQC configuration from a backup.  I had to reinstall and I'd like to be able to use my old settings.  

I was new to CQC when they shut the site down, but really like its stability vs other options...and want to get this running again.

Thanks for any tips.

[kfly]

Does this help? sic0048 had a thread on the original forum. maybe this CQC article from the waybackmachine helps?

https://web.archive.org/web/202206242313...?tid=11194

Pretty sure also I have done a fresh complete CQC software install with the same version as backup. Then just restored all  the C:/Program Filesx86/CQC/CQCData folder files from backup.

[Spot]

Does this help? sic0048 had a thread on the original forum. maybe this CQC article from the waybackmachine helps?

https://web.archive.org/web/202206242313...?tid=11194

Pretty sure also I have done a fresh complete CQC software install with the same version as backup. Then just restored all  the C:/Program Filesx86/CQC/CQCData folder files from backup.

It did help.  

Apparently my backups were corrupted, but I was able to get into the Admin Interface so that I could see what events & drivers I had set up.

I eventually had to do a clean install and reconstruct my settings.

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

[kfly]

Does this help? sic0048 had a thread on the original forum. maybe this CQC article from the waybackmachine helps?

https://web.archive.org/web/202206242313...?tid=11194

Pretty sure also I have done a fresh complete CQC software install with the same version as backup. Then just restored all  the C:/Program Filesx86/CQC/CQCData folder files from backup.

It did help.  

Apparently my backups were corrupted, but I was able to get into the Admin Interface so that I could see what events & drivers I had set up.

I eventually had to do a clean install and reconstruct my settings.

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

I have uploaded them here if needed.
https://cqccommunity.com/Web2/CQCDocs/CQCDocs.html?topic=/&page=/Overview

[Spot]

[quote pid="50" dateline="1741393671"]
Thanks!!

Too bad we don't have an archive of the original forums...
[/quote]

I have uploaded them here if needed.
https://cqccommunity.com/Web2/CQCDocs/CQCDocs.html?topic=/&page=/Overview

[kblagron]

Does this help? sic0048 had a thread on the original forum. maybe this CQC article from the waybackmachine helps?

https://web.archive.org/web/202206242313...?tid=11194

Pretty sure also I have done a fresh complete CQC software install with the same version as backup. Then just restored all  the C:/Program Filesx86/CQC/CQCData folder files from backup.

It did help.  

Apparently my backups were corrupted, but I was able to get into the Admin Interface so that I could see what events & drivers I had set up.

I eventually had to do a clean install and reconstruct my settings.

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

---

Thanks

Dave

During the initial install, their is a setting for which port you want to use for the Master Server's web server and also the help files.  As I recall you can change that so it is not a standard port like 80, and they can be different.

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave

Maddeningly enough...I cannot get to the help documents.  I keep getting the message "The address of Master Server's web server could not be gotten"

Thanks

Dave